medias® professional – Product catalogue
www.ina.com |  www.fag.com |  Contact |  Legal notice |  Conditions of use |  Info
Language
Search
Rolling and plain bearings, accessories
Transparent classification of our bearings for rotary motion.
Linear guidance systems
Transparent classification of our linear bearings.
Selection wizards
Bearing selection
The wizard will assist you in the selection of the correct bearing for your design.
Linear selection
The wizard will assist you in the selection of the correct linear guidance system for your design.
Housing selection
The wizard will assist you in the selection of the correct housing for your design
Application examples
Suggestions for your daily work.
Lubricant selection
Lubrication is a design element. You can find the right grease or oil here.
Principles
Here you can find fundamental knowledge on the calculation, lubrication and fitting of bearings.
Lexicon
Here you can find explanations of terms in bearing technology
Interchange list - designations
From this list, you can use the old designation to find the new uniform designation of INA and FAG.
medias® campus
Our online training courses gives you the necessary rolling bearing knowledge in the form of short learning units.
medias® interchange
This function determines appropriate INA and FAG bearings based on designations from other manufacturers.
Help
Is something unclear? Our help system can assist you.
medias® gadget
Integrate the medias product search in your webpage.
medias® Home Linear guidance systems LTE LTE50-B
Series selection
Product selection
Product data
Description
Calculation
CAD
Shopping basket
Datasheet

Linear tables LTE50-B

without drive

Linear tables LTE50-B, without drive
Compressive loadTensile loadMoments about all axesGrease lubrication
Linear tables LTE50-B, without drive
Linear tables LTE50-B, without drive
Linear tables LTE50-B, without drive
 
H2 96  mm 
   
A 280  mm 
   
Ltot GH x 1,24 + 362 
  Only valid with standard bellows.
For a table without bellows:

L tot = A + 2 x B1 + total stroke
and Xmin = (A/2) + B1.

(GH = total stroke)
 
B1 30  mm 
   
E1 250  mm 
   
E2 240  mm 
   
G1 140  mm 
   
g1 11  mm 
   
H 48  mm 
   
H1 100  mm 
   
H5 44  mm 
   
M M16 
   
R 152  mm 
   
Rx 163  mm 
   
S 14  mm 
   
S 20 x 15,5 
   
S1 M16x34 
   
Xmin GH x 0,120 + 181 
  Only valid with standard bellows.
For a table without bellows:

L tot = A + 2 x B1 + total stroke
and Xmin = (A/2) + B1.

(GH = total stroke)
 
m 18  kg 
  Mass of carriage
mtot Ltot x 0,03 + 21  kg 
  Mass of complete table:
L tot x 0,03 + 21
NIP A3 
  Lubrication nipple
  KB 50100 P 
  Linear ball bearing used in carriage

The shaft deflection must be taken into consideration.
For detailed design of the guidance system, see Catalogue PF1.
C 19500  N 
  Basic load ratings: Load direction Y I-II

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
C0 25000  N 
  Basic load ratings: Load direction Y I-II

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
C 19500  N 
  Basic load ratings: Load direction Z III

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
C0 25000  N 
  Basic load ratings: Load direction Z III

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
M0x 1920  Nm 
  Moment ratings:

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
M0y 2050  Nm 
  Moment ratings:

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
M0z 2050  Nm 
  Moment ratings:

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.