medias® professional – Product catalogue
www.ina.com |  www.fag.com |  Contact |  Legal notice |  Conditions of use |  Info
Language
Search
Rolling and plain bearings, accessories
Transparent classification of our bearings for rotary motion.
Linear guidance systems
Transparent classification of our linear bearings.
Selection wizards
Bearing selection
The wizard will assist you in the selection of the correct bearing for your design.
Linear selection
The wizard will assist you in the selection of the correct linear guidance system for your design.
Housing selection
The wizard will assist you in the selection of the correct housing for your design
Application examples
Suggestions for your daily work.
Lubricant selection
Lubrication is a design element. You can find the right grease or oil here.
Principles
Here you can find fundamental knowledge on the calculation, lubrication and fitting of bearings.
Lexicon
Here you can find explanations of terms in bearing technology
Interchange list - designations
From this list, you can use the old designation to find the new uniform designation of INA and FAG.
medias® campus
Our online training courses gives you the necessary rolling bearing knowledge in the form of short learning units.
medias® interchange
This function determines appropriate INA and FAG bearings based on designations from other manufacturers.
Help
Is something unclear? Our help system can assist you.
medias® gadget
Integrate the medias product search in your webpage.
medias® Home Linear guidance systems LTE..- LTE20-1610-B
Series selection
Product selection
Product data
Description
Calculation
CAD
Shopping basket
Datasheet

Linear tables LTE20-1610-B

with ball screw drive

Linear tables LTE20-1610-B, with ball screw drive
Compressive loadTensile loadMoments about all axesGrease lubrication
Linear tables LTE20-1610-B, with ball screw drive
Linear tables LTE20-1610-B, with ball screw drive
Linear tables LTE20-1610-B, with ball screw drive
 
H2 46  mm 
   
A 130  mm 
   
Ltot GH x 1,33 + 199 
  Only valid with standard bellows.
For a table without bellows:

L tot = A + B1 + B2 + total stroke
and Xmin = (A/2) + B2.

(GH = total stroke)
 
a 62  mm 
  Tolerance: +/-0,2
B1 20  mm 
   
B2 29  mm 
   
b 30  mm 
  Tolerance: +/-0,2
d1 9  mm 
  Tolerance for diameter: h7

Thread witness marks may be present on the pin.
d2 50g7  mm 
   
E1 115  mm 
   
E2 108  mm 
   
G1 65  mm 
  Position of lubrication nipples:
2x for linear ball bearings
G2  
  New pitch values are under development. Please ask for further information.
G3 12  mm 
  Position of lubrication nipples:
1x for locating bearing
G4 10  mm 
  Position of lubrication nipples:
1x for non-locating bearing
g1 7  mm 
  Position of lubrication nipples:
2x for linear ball bearings
g2  
  New pitch values are under development. Please ask for further information.
g3 12  mm 
  Position of lubrication nipples:
1x for locating bearing
g4  
  Position of lubrication nipples:
1x for non-locating bearing
H 23  mm 
   
H1 48  mm 
   
H5 21  mm 
   
L2 37  mm 
   
L3 18  mm 
   
L4 8  mm 
   
M M10 
   
R 72  mm 
   
Rx 74,6  mm 
   
S 6,7  mm 
   
S 11 x 8,4 
   
S1 M8x18 
  Thread:
M.. x depth
S4 M6x15 
  Thread:
M.. x depth
Xmin GH x 0,167 + 104 
  Only valid with standard bellows.
For a table without bellows:

L tot = A + B1 + B2 + total stroke
and Xmin = (A/2) + B2.

(GH = total stroke)
 
m 1,9  kg 
  Mass of carriage
mtot Ltot x 0,006 + 3,4  kg 
  Mass of complete table:
L tot x 0,006 + 3,4
  KB 2045 P 
  Linear ball bearing:
KB..-P
C 3600  N 
  Basic load ratings: Load direction Y I-II

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
C0 4900  N 
  Basic load ratings: Load direction Y I-II

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
C 3600  N 
  Basic load ratings: Load direction Z III

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
C0 4900  N 
  Basic load ratings: Load direction Z III

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
M0x 177  Nm 
  Moment ratings:

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
M0y 184  Nm 
  Moment ratings:

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
M0z 184  Nm 
  Moment ratings:

Basic load rating when load is evenly distributed over all four linear ball bearings.
The stated basic loads and moments cannot be added together.
  1610 
  New pitch values are under development. Please ask for further information.
  M 
  Nut design:

M = cylindrical threaded nut, without preload
MM = double cylindrical threaded nut, with preload
C 23000  N 
  Basic load ratings for nut

Basic dynamic load rating C

Dynamic loads to DIN 69 051, Part 4, issued 1978.
C0 26000  N 
  Basic load ratings for nut

Basic static load rating Co.
  ZKLN1034-2RS 
  Rolling bearings
C 13400  N 
  Maximum axial load on locating bearing

Basic dynamic load rating C
C0 18800  N 
  Maximum axial load on locating bearing

Basic static load rating Co
NIP A1 
  Lubrication nipple
   
  The shaft deflection must be taken into consideration.
For detailed design of the guidance system, see Catalogue PF1.
   
  M = cylindrical threaded nut, without preload

MM = double cylindrical threaded nut, with preload